Signs it’s time for gutter replacement
- Drips from joints or corners even after resealing
- Gutters that hold water (no fall) or overflow in modest rain
- Black staining or moss tracks on brickwork below the eaves
- Loose brackets, sagging runs or discoloured, brittle plastic
- Downpipes that back up or discharge at the base of walls
If two or more apply, planned gutter replacement is safer (and cheaper long-term) than another round of mastic and hope.
Choosing the right profile and material
- uPVC guttering (most popular): durable, low-maintenance and cost-effective with quick, clean installation. Available in half-round, square and deep-flow profiles, plus colours to match your fascias.
- Deep-flow profiles: higher capacity for large or steep roofs; ideal for valleys and long runs where stormwater peaks quickly.
- Colour choices: White, Black, Anthracite Grey and Browns, with matching downpipes, shoes and bends for a consistent finish.
We size capacity to your roof area and rainfall exposure, not guesswork.
Getting the falls right — small angles, big difference
A “flat” gutter won’t drain. We set subtle, consistent falls towards outlets (usually 1:600 to 1:350 depending on run length and profile), check them with a level and sightline, then test with water. Correct fall + correct outlet placement = quiet performance in heavy rain.
Leak-free joints and corners — built to be serviceable
We use manufacturer-approved, compression-sealed unions and corners rather than relying on blobs of silicone. Benefits:
- Movement-tolerant during hot/cold cycles
- Easy to service or replace in future
- Cleaner look with factory-neat seals
On older properties where walls wander, we adjust bracket spacing to keep joints stress-free.
Downpipes — where the water actually leaves
Downpipes are the last mile. We:
- Position outlets to avoid long “flat” runs that invite puddling.
- Fix downpipes on proper centres so they don’t tap or rattle.
- Route to gullies or soakaways sensibly, adding swan-necks and bends where needed without creating choke points.
- Finish with colour-matched shoes or hopper heads that look deliberate, not improvised.
If your drains are sensitive, we’ll suggest leaf guards or easy-clean strainers.
Pairing guttering with fascias and soffits
Gutters only run true when they’re fixed to sound fascia boards. If your fascias are soft or wavy, we’ll price options to renew them at the same time. We can also colour-match new gutters to existing fascias and soffits for a joined-up look.
New gutters over conservatories, dormers and tricky junctions
The awkward bits are where poor jobs fail first. We handle:
- Box ends that shed water properly instead of trapping it
- Valley discharge into deep-flow profiles to swallow peak flows
- Conservatory over-sails with purpose-made covers and careful sequencing
- Dormer tie-ins with crisp trims and correctly set mini-gutters
It’s the difference between “it’ll do” and “that looks built with the house”.
Leaf, moss and debris control — prevention beats cure
- Balloon guards or wire strainers at outlets to stop leaf clumps travelling down the pipe
- Leaf-guard meshes on tree-heavy plots (we’ll advise where they genuinely help)
- Downpipe access points for quick rodding without dismantling
We’ll be honest: not every home needs guards. Sometimes a quick post-autumn clean is the simpler, better solution.
Maintenance — five-minute habits that add years
- Clear leaves after autumn and again in spring if trees are near.
- Check joints and corners after big storms; re-clip if anything has crept.
- Keep downpipe gullies free of grit so they don’t back up.
- Rinse algae streaks off façades early — it’s easier when fresh.
- If you hear rattling, a single loose bracket could be the culprit — call us before it worsens.
Our installation process — safe, tidy and precise
- Survey & options
We measure roof areas, note valley positions, check fascia condition and plan outlet/downpipe locations. You receive an itemised quote for guttering, any gutter replacement, and optional fascia/soffit works. - Access & protection
Scaffold or safe access towers as needed. We protect paths, drives and planting. - Strip-out
Old runs and brackets removed; walls and fascia edges checked and prepped. - Brackets & lines
We set starter and end brackets to the correct fall, snap chalk lines, then fix intermediate brackets at manufacturer centres (closer in exposed zones). - Hang & connect
New lengths are cut cleanly, unions and corners clipped with fresh seals, and outlets positioned for efficient drainage. - Downpipes & discharge
Pipes are aligned, fixed, and tied into gullies with neat shoes or bends. We avoid sharp, flow-killing zig-zags. - Test & tidy
We water-test for leaks and pooling, adjust if needed, then clean down and remove waste.
Repair vs replacement — straight talk before we start
- Repair suits isolated issues: a failed joint, a bracket replacement, a localised fall correction.
- Replacement wins when plastics are brittle, runs are wavy, or leaks appear across multiple joints.
We’ll show photos, explain causes and price both routes where it’s borderline.
Costs and value — where your budget goes
- Length of runs and height/access requirements
- Profile choice (half-round, square, deep-flow) and colour
- Number of corners, outlets and downpipes
- Fascia condition and any strengthening needed
- Junction complexity (valleys, dormers, conservatory interfaces)
You’ll receive a clear, itemised figure so you can see exactly what you’re paying for.
Frequently asked questions about guttering
Ready to stop drips, straighten lines and move rainwater the right way?
Send a couple of photos of the problem spots — corners, overflows, sagging runs — and we’ll map a straightforward fix or new gutters plan. Expect neat falls, quiet operation and a colour-matched finish that looks like it’s always been there.
Prefer to talk it through? Call 0800 233 5576 and speak with our guttering team.
